SEL Series｜Straight Side Eccentric Gear Link-Motion Press

Products

SEL Series｜Straight Side Eccentric Gear Link-Motion Press

The prime choice of press equipment for forming process of large pieces, which makes it applicable for forming of large automotive parts. The eccentric gear and connecting rods are adopted for the drive component. The design of low energy consumption can effectively save more than 20% of energy.

Model : SEL2-400~1200 / SEL4-400~2400

Q'ty :

Catalogs

# Tandem Press Line

# Transfer

# Tonnage(kN) 3000~6500

# Tonnage(kN) 8000~12000

# Tonnage(kN) 16000↑

# Stroke Length 450↑

# Bolster Area(L-R) 2500~3400

# Bolster Area(L-R) 3400↑

Designed with tie-rod structure on the frame and adopting gear driving component with four connecting rods, the rigidity of main body increases extensively.The soft contact and processing at constant speed during press forming extensively reduces vibration, noise and heat, as well as extending die lifetime.
The combination of pneumatic die cushion for big tonnage with tightening and adjusting component can address the needs for different stroke and action.
With the use of high torque wet clutch/ brake, the lifetime of clutch increases and environmental protection is ensured.
The highly respondent Hydraulic Overload Protector (HOLP) can effectively fix die stuck and prevent overloading.
The design of piston guide pillar extensively absorbs lateral support to the connecting rod for precise and stable movement of the slide block.

SI Unit
Imperial Unit

Model				SEL2-400	SEL2-500	SEL2-600
Type				S	S	S
Capacity			kN	4000	5000	6000
Stroke Length			mm	500	500	500
Strokes per Minute			SPM	15~26	12~24	12~22
Tonnage Rating Point			mm	13	13	13
Die Height			mm	700	800	800
Slide Adjustment			mm	300	400	400
Slide Area(LR×FB)		1	mm	2500×1400	2500×1450	2500×1550
		2		2800×1400	2800×1450	2800×1550
		3		3100×1400	3100×1450	3100×1550
		4		3400×1400	3400×1450	3400×1550
		5		3700×1400	3700×1450	3700×1550
Bolster Area(LR×FB)		1	mm	2500×1400	2500×1450	2500×1550
		2		2800×1400	2800×1450	2800×1550
		3		3100×1400	3100×1450	3100×1550
		4		3400×1400	3400×1450	3400×1550
		5		3400×1400	3400×1450	3700×1550
Bolster Thickness			mm	180	180	250
Window Opening	Bolster Only	FB × UD	mm	1200×600	1200×700	1350×700
	Front to Back Rolling Bolster			1200×600	1200×700	1350×700
	Left to Right Rolling Bolster			1700×800	1750×900	1850×900
Max. Upper Die Weight*			Ton	5	6	6
Required Air Pressure			MPa	0.55	0.55	0.55
Bolster Height	Fixed Bolster		mm	850	850	850
Bolster Height	Rolling Bolster		mm	660	660	660
Main Motor	w/o Die Cushion		kW×P	45×4	55×4	55×4
Main Motor	w/ Die Cushion		kW×P	45×4	55×4	55×4
Die Cushion	Type			cylinder	cylinder	cylinder
	Capacity		kN	600	800	1000
	Stroke Length		mm	200	220	220
	Adjustment		mm	200	220	220
Cushion Pad Area(LR×FB)		1	mm	2000×900	2000×950	2000×950
		2		2300×900	2300×950	2300×950
		3		2600×900	2600×950	2600×950
		4		2900×900	2900×950	2900×950

Model				SEL2-800	SEL2-1000	SEL2-1200
Type				S	S	S
Capacity			kN	8000	10000	12000
Stroke Length			mm	600	600	800
Strokes per Minute			SPM	10~18	10~18	10~18
Tonnage Rating Point			mm	13	13	13
Die Height			mm	1000	1000	1100
Slide Adjustment			mm	400	400	500
Slide Area(LR×FB)		1	mm	2800×1700	3100×1700	3400×1700
		2		3100×1700	3400×1700	3700×1700
		3		3400×1700	3700×1700	4000×1700
		4		3700×1700	4000×1700	4300×1700
		5		4000×1700	4300×1700	4600×1700
Bolster Area(LR×FB)		1	mm	2800×1700	3100×1700	3400×1700
		2		3100×1700	3400×1700	3700×1700
		3		3400×1700	3700×1700	4000×1700
		4		3700×1700	4000×1700	4300×1700
		5		4000×1700	4300×1700	4600×1700
Bolster Thickness			mm	250	250	300
Window Opening	Bolster Only	FB × UD	mm	1500×900	1500×900	1500×1000
	Front to Back Rolling Bolster			1500×900	1500×900	1500×1000
	Left to Right Rolling Bolster			2000×1100	2000×1100	2000×1200
Max. Upper Die Weight*			Ton	7	7	8
Required Air Pressure			MPa	0.55	0.55	0.55
Bolster Height	Fixed Bolster		mm	850	850	850
Bolster Height	Rolling Bolster		mm	660	740	740
Main Motor	w/o Die Cushion		kW×P	75×4	90×4	90×4
Main Motor	w/ Die Cushion		kW×P	75×4	90×4	110×4
Die Cushion	Type			cylinder	cylinder	cylinder
	Capacity		kN	1200**	1500	2000
	Stroke Length		mm	220	220	220
	Adjustment		mm	220	220	220
Cushion Pad Area(LR×FB)		1	mm	2300×1300	2600×1300	2900×1300
		2		2600×1300	2900×1300	3200×1300
		3		2900×1300	3200×1300	3500×1300
		4		3200×1300	3500×1300	3800×1300

Model				SEL4-400	SEL4-500	SEL4-600
Type				S	S	S
Capacity			kN	4000	5000	6000
Stroke Length			mm	500	500	500
Strokes per Minute			SPM	15~26	12~24	12~22
Tonnage Rating Point			mm	13	13	13
Die Height			mm	700	800	800
Slide Adjustment			mm	300	400	400
Slide Area(LR×FB)		1	mm	2500×2000	2500×2000	2500×2000
		2		2800×2000	2800×2000	2800×2000
		3		3100×2000	3100×2000	3100×2000
		4		3400×2000	3400×2000	3400×2000
		5		3700×2000	3700×2000	3700×2000
Bolster Area(LR×FB)		1	mm	2500×2000	2500×2000	2500×2000
		2		2800×2000	2800×2000	2800×2000
		3		3100×2000	3100×2000	3100×2000
		4		3400×2000	3400×2000	3400×2000
		5		3700×2000	3700×2000	3700×2000
Bolster Thickness			mm	180	180	250
Window Opening	Bolster Only	FB × UD	mm	1800×600	1800×700	1800×700
	Front to Back Rolling Bolster			1800×600	1800×700	1800×700
	Left to Right Rolling Bolster			2300×800	2300×900	2300×900
Max. Upper Die Weight*			Ton	8	8	9
Required Air Pressure			MPa	0.55	0.55	0.55
Bolster Height	Fixed Bolster		mm	850	850	850
Bolster Height	Rolling Bolster		mm	660	660	660
Main Motor	w/o Die Cushion		kW×P	45×4	55×4	55×4
Main Motor	w/ Die Cushion		kW×P	45×4	55×4	55×4
Die Cushion	Type			cylinder	cylinder	cylinder
	Capacity		kN	600	800	1000
	Stroke Length		mm	200	220	220
	Adjustment		mm	200	220	220
Cushion Pad Area(LR×FB)		1	mm	2000×1300	2000×1300	2000×1300
		2		2300×1300	2300×1300	2300×1300
		3		2600×1300	2600×1300	2600×1300
		4		2900×1300	2900×1300	2900×1300

Model				SEL4-800	SEL4-1000	SEL4-1200
Type				S	S	S
Capacity			kN	8000	10000	12000
Stroke Length			mm	600	600	800
Strokes per Minute			SPM	10~20	10~20	10~20
Tonnage Rating Point			mm	13	13	13
Die Height			mm	1000	1000	1100
Slide Adjustment			mm	400	400	500
Slide Area(LR×FB)		1	mm	2800×2200	3100×2200	3400×2200
		2		3100×2200	3400×2200	3700×2200
		3		3400×2200	3700×2200	4000×2200
		4		3700×2200	4000×2200	4300×2200
		5		4000×2200	4300×2200	4600×2200
Bolster Area(LR×FB)		1	mm	2800×2200	3100×2200	3400×2200
		2		3100×2200	3400×2200	3700×2200
		3		3400×2200	3700×2200	4000×2200
		4		3700×2200	4000×2200	4300×2200
		5		4000×2200	4300×2200	4600×2200
Bolster Thickness			mm	250	250	300
Window Opening	Bolster Only	FB × UD	mm	2000×900	2000×900	2000×1000
	Front to Back Rolling Bolster			2000×900	2000×900	2000×1000
	Left to Right Rolling Bolster			2500×1100	2500×1100	2500×1200
Max. Upper Die Weight*			Ton	10	10	11
Required Air Pressure			MPa	0.55	0.55	0.55
Bolster Height	Fixed Bolster		mm	850	850	850
Bolster Height	Rolling Bolster		mm	660	740	740
Main Motor	w/o Die Cushion		kW×P	75×4	90×4	90x4
Main Motor	w/ Die Cushion		kW×P	75×4	90×4	110x4
Die Cushion	Type			cylinder	cylinder	cylinder
	Capacity		kN	1200*	1500	2000
	Stroke Length		mm	250	250	250
	Adjustment		mm	250	250	250
Cushion Pad Area(LR×FB)		1	mm	2300×1500	2600×1500	2900×1500
		2		2600×1500	2900×1500	3200×1500
		3		2900×1500	3200×1500	3500×1500
		4		3200×1500	3500×1500	3800×1500

Model				SEL4-1600	SEL4-2000	SEL4-2400
Type				S	S	S
Capacity			kN	16000	20000	24000
Stroke Length			mm	800	900	1000
Strokes per Minute			SPM	10~20	10~20	10~20
Tonnage Rating Point			mm	13	13	13
Die Height			mm	1200	1300	1400
Slide Adjustment			mm	500	600	600
Slide Area(LR×FB)		1	mm	3400×2200	4000×2200	4000×2200
		2		3700×2200	4300×2200	4300×2200
		3		4000×2200	4600×2200	4600×2200
		4		4300×2200	4900×2200	4900×2200
		5		4600×2200	5200×2200	5200×2200
Bolster Area(LR×FB)		1	mm	3400×2200	4000×2200	4000×2200
		2		3700×2200	4300×2200	4300×2200
		3		4000×2200	4600×2200	4600×2200
		4		4300×2200	4900×2200	4900×2200
		5		4600×2200	5200×2200	5200×2200
Bolster Thickness			mm	300	300	300
Window Opening	Bolster Only	FB × UD	mm	2000×1100	2000×1200	2000×1300
	Front to Back Rolling Bolster			2000×1100	2000×1200	2000×1300
	Left to Right Rolling Bolster			2500×1300	2500×1400	2500×1500
Max. Upper Die Weight*			Ton	13	15	20
Required Air Pressure			MPa	0.55	0.55	0.55
Bolster Height	Fixed Bolster		mm	850	850	850
Bolster Height	Rolling Bolster		mm	740	740	740
Main Motor	w/o Die Cushion		kW×P	130×4	150×4	185×4
Main Motor	w/ Die Cushion		kW×P	150×4	185×4	225×4
Die Cushion	Type			cylinder	cylinder	cylinder
	Capacity		kN	2400	3000	3000
	Stroke Length		mm	250	300	300
	Adjustment		mm	250	300	300
Cushion Pad Area(LR×FB)		1	mm	2900×1500	3500×1500	3500×1500
		2		3200×1500	3800×1500	3800×1500
		3		3500×1500	4100×1500	4100×1500
		4		3800×1500	4400×1500	4400×1500

* Upper die weight may vary in table size. Please contact your sales representative for more information.
** For selecting 1200kN, 1500kN and 2000kN air cylinder die cushions, bolster area in FB should be at least 1700mm.
*** For selecting 2400kN air cylinder die cushions, bolster area in FB should be at least 1900mm.
**** For SEL2-800-1, only 1000kN die cushion is available.

* For SEL4-800-1, only 1000kN die cushion is available.
※ Slide and bolster area up to 5500x1550 by request.
※ This specification is subject to change without notice.

Model				SEL2-440		SEL2-550		SEL2-660
Type				S	H	S	H	S	H
Capacity			U.S. Ton	440		550		660
Stroke Length			in	19.69		19.69		19.69
Strokes per Minute			SPM	15~26		12~24		12~22
Tonnage Rating Point			in	0.51	0.26	0.51	0.26	0.51	0.26
Die Height			in	27.56		31.50		31.50
Slide Adjustment			in	11.81		15.75		15.75
Slide Area(LR×FB)		1	in	98.43×55.12		98.43×57.09		98.43×61.02
		2		110.24×55.12		110.24×57.09		110.24×61.02
		3		122.05×55.12		122.05×57.09		122.05×61.02
		4		133.86×55.12		133.86×57.09		133.86×61.02
		5		145.67×55.12		145.67×57.09		145.67×61.02
Bolster Area(LR×FB)		1	in	98.43×55.12		98.43×57.09		98.43×61.02
		2		110.24×55.12		110.24×57.09		110.24×61.02
		3		122.05×55.12		122.05×57.09		122.05×61.02
		4		133.86×55.12		133.86×57.09		133.86×61.02
		5		145.67×55.12		145.67×57.09		145.67×61.02
Bolster Thickness			in	7.09		7.09		9.84
Window Opening	Bolster Only	FB × UD	in	47.24×23.62		47.24×27.56		53.15×27.56
	Front to Back Rolling Bolster			47.24×23.62		47.24×27.56		53.15×27.56
	Left to Right Rolling Bolster			66.93×31.5		68.9×35.43		72.83×35.43
Max. Upper Die Weight*			LBS	11000		13200		13200
Required Air Pressure			PSI	85.34		85.34		85.34
Bolster Height	Fixed Bolster		in	33.46		33.46		33.46
	Rolling Bolster			25.98		25.98		25.98
Main Motor	w/o Die Cushion		HP×P	60×4		75×4		75×4
	w/ Die Cushion
Die Cushion	Type			cylinder		cylinder		cylinder
	Capacity		U.S. Ton	66		88		110
	Stroke Length		in	7.87		8.66		8.66
	Adjustment		in	7.87		8.66		8.66
Cushion Pad Area(LR×FB)		1	in	78.74×35.43	—	78.74×37.4	—	78.74×37.4	—
		2		90.55×35.43	—	90.55×37.4	—	90.55×37.4	—
		3		102.36×35.43	—	102.36×37.4	—	102.36×37.4	—
		4		114.17×35.43	—	114.17×37.4	—	114.17×37.4	—

Model				SEL2-880	SEL2-1100	SEL2-1320
Type				S	S	S
Capacity			U.S. Ton	880	1100	1320
Stroke Length			in	23.62	23.62	31.50
Strokes per Minute			SPM	10~18	10~18	10~18
Tonnage Rating Point			in	0.51	0.51	0.51
Die Height			in	39.37	39.37	43.31
Slide Adjustment			in	15.75	15.75	19.69
Slide Area(LR×FB)		1	in	110.24×66.93	122.05×66.93	133.86×66.93
		2		122.05×66.93	133.86×66.93	145.67×66.93
		3		133.86×66.93	145.67×66.93	157.48×66.93
		4		145.67×66.93	157.48×66.93	169.29×66.93
		5		157.48×66.93	169.29×66.93	181.1×66.93
Bolster Area(LR×FB)		1	in	110.24×66.93	122.05×66.93	133.86×66.93
		2		122.05×66.93	133.86×66.93	145.67×66.93
		3		133.86×66.93	145.67×66.93	157.48×66.93
		4		145.67×66.93	157.48×66.93	169.29×66.93
		5		157.48×66.93	169.29×66.93	181.1×66.93
Bolster Thickness			in	9.84	9.84	11.81
Window Opening	Bolster Only	FB × UD	in	59.06×35.43	59.06×35.43	59.06×39.37
	Front to Back Rolling Bolster			59.06×35.43	59.06×35.43	59.06×39.37
	Left to Right Rolling Bolster			78.74×43.31	78.74×43.31	78.74×47.24
Max. Upper Die Weight*			LBS	15400	15400	17600
Required Air Pressure			PSI	85.34	85.34	85.34
Bolster Height	Fixed Bolster		in	33.46	33.46	33.46
Bolster Height	Rolling Bolster		in	25.98	29.13	29.13
Main Motor	w/o Die Cushion		HP×P	100×4	125×4	125×4
Main Motor	w/ Die Cushion		HP×P	100×4	125×4	150×4
Die Cushion	Type			cylinder	cylinder	cylinder
	Capacity		U.S. Ton	132(*)	165	220
	Stroke Length		in	8.66	8.66	8.66
	Adjustment		in	8.66	8.66	8.66
Cushion Pad Area(LR×FB)		1	in	90.55×51.18	102.36×51.18	114.17×51.18
		2		102.36×51.18	114.17×51.18	125.98×51.18
		3		114.17×51.18	125.98×51.18	137.8×51.18
		4		125.98×51.18	137.8×51.18	149.61×51.18

Model				SEL4-550	SEL4-660	SEL4-880
Type				S	S	S
Capacity			U.S. Ton	550	660	880
Stroke Length			in	19.69	19.69	23.62
Strokes per Minute			SPM	12~24	12~22	10~20
Tonnage Rating Point			in	0.51	0.51	0.51
Die Height			in	31.50	31.50	39.37
Slide Adjustment			in	15.75	15.75	15.75
Slide Area(LR×FB)		1	in	98.43×78.74	98.43×78.74	110.24×86.61
		2		110.24×78.74	110.24×78.74	122.05×86.61
		3		122.05×78.74	122.05×78.74	133.86×86.61
		4		133.86×78.74	133.86×78.74	145.67×86.61
		5		145.67×78.74	145.67×78.74	157.48×86.61
Bolster Area(LR×FB)		1	in	98.43×78.74	98.43×78.74	110.24×86.61
		2		110.24×78.74	110.24×78.74	122.05×86.61
		3		122.05×78.74	122.05×78.74	133.86×86.61
		4		133.86×78.74	133.86×78.74	145.67×86.61
		5		145.67×78.74	145.67×78.74	157.48×86.61
Bolster Thickness			in	7.09	9.84	9.84
Window Opening	Bolster Only	FB × UD	in	70.87×27.56	70.87×27.56	78.74×35.43
	Front to Back Rolling Bolster			70.87×27.56	70.87×27.56	78.74×35.43
	Left to Right Rolling Bolster			90.55×35.43	90.55×35.43	98.43×43.31
Max. Upper Die Weight*			LBS	17600	19800	22000
Required Air Pressure			PSI	85.34	85.34	85.34
Bolster Height	Fixed Bolster		in	25.98	25.98	25.98
Bolster Height	Rolling Bolster		in	25.98	25.98	25.98
Main Motor	w/o Die Cushion		HP×P	75×4	75×4	100×4
Main Motor	w/ Die Cushion		HP×P	75×4	75×4	100×4
Die Cushion	Type			cylinder	cylinder	cylinder
	Capacity		U.S. Ton	88	110	132(*)
	Stroke Length		in	8.66	8.66	9.84
	Adjustment		in	8.66	8.66	9.84
Cushion Pad Area(LR×FB)		1	in	78.74×51.18	78.74×51.18	90.55×59.06
		2		90.55×51.18	90.55×51.18	102.36×59.06
		3		102.36×51.18	102.36×51.18	114.17×59.06
		4		114.17×51.18	114.17×51.18	125.98×59.06

Model				SEL4-1100	SEL4-1320	SEL4-1760
Type				S	S	S
Capacity			U.S. Ton	1100	1320	1760
Stroke Length			in	23.62	31.50	31.50
Strokes per Minute			SPM	10~20	10~20	10~20
Tonnage Rating Point			in	0.51	0.51	0.51
Die Height			in	39.37	43.31	47.24
Slide Adjustment			in	15.75	19.69	19.69
Slide Area(LR×FB)		1	in	122.05×86.61	133.86×86.61	133.86×86.61
		2		133.86×86.61	145.67×86.61	145.67×86.61
		3		145.67×86.61	157.48×86.61	157.48×86.61
		4		157.48×86.61	169.29×86.61	169.29×86.61
		5		169.29×86.61	181.1×86.61	181.1×86.61
Bolster Area(LR×FB)		1	in	122.05×86.61	133.86×86.61	133.86×86.61
		2		133.86×86.61	145.67×86.61	145.67×86.61
		3		145.67×86.61	157.48×86.61	157.48×86.61
		4		157.48×86.61	169.29×86.61	169.29×86.61
		5		169.29×86.61	181.1×86.61	181.1×86.61
Bolster Thickness			in	9.84	11.81	11.81
Window Opening	Bolster Only	FB × UD	in	78.74×35.43	78.74×39.37	78.74×43.31
	Front to Back Rolling Bolster			78.74×35.43	78.74×39.37	78.74×43.31
	Left to Right Rolling Bolster			98.43×43.31	98.43×47.24	98.43×51.18
Max. Upper Die Weight*			LBS	22000	24200	28600
Required Air Pressure			PSI	85.34	85.34	85.34
Bolster Height	Fixed Bolster		in	29.13	29.13	29.13
Bolster Height	Rolling Bolster		in	29.13	29.13	29.13
Main Motor	w/o Die Cushion		HP×P	125×4	125×4	175x4
Main Motor	w/ Die Cushion		HP×P	125×4	150x4	200x4
Die Cushion	Type			cylinder	cylinder	cylinder
	Capacity		U.S. Ton	165	220	264
	Stroke Length		in	9.84	9.84	9.84
	Adjustment		in	9.84	9.84	9.84
Cushion Pad Area(LR×FB)		1	in	102.36×59.06	114.17×59.06	114.17×59.06
		2		114.17×59.06	125.98×59.06	125.98×59.06
		3		125.98×59.06	137.8×59.06	137.8×59.06
		4		137.8×59.06	149.61×59.06	149.61×59.06

Model				SEL4-2200	SEL4-2640
Type				S	S
Capacity			U.S. Ton	2200	2640
Stroke Length			in	35.43	39.37
Strokes per Minute			SPM	10~20	10~20
Tonnage Rating Point			in	0.51	0.51
Die Height			in	51.18	55.12
Slide Adjustment			in	23.62	23.62
Slide Area(LR×FB)		1	in	157.48×86.61	157.48×86.61
		2		169.29×86.61	169.29×86.61
		3		181.1×86.61	181.1×86.61
		4		192.91×86.61	192.91×86.61
		5		204.72×86.61	204.72×86.61
Bolster Area(LR×FB)		1	in	157.48×86.61	157.48×86.61
		2		169.29×86.61	169.29×86.61
		3		181.1×86.61	181.1×86.61
		4		192.91×86.61	192.91×86.61
		5		204.72×86.61	204.72×86.61
Bolster Thickness			in	11.81	11.81
Window Opening	Bolster Only	FB × UD	in	78.74×47.24	78.74×51.18
	Front to Back Rolling Bolster			78.74×47.24	78.74×51.18
	Left to Right Rolling Bolster			98.43×55.12	98.43×59.06
Max. Upper Die Weight*			LBS	33000	44000
Required Air Pressure			PSI	85.34	85.34
Bolster Height	Fixed Bolster		in	29.13	29.13
Bolster Height	Rolling Bolster		in	29.13	29.13
Main Motor	w/o Die Cushion		HP×P	200×4	250×4
Main Motor	w/ Die Cushion		HP×P	250×4	300×4
Die Cushion	Type			cylinder	cylinder
	Capacity		U.S. Ton	330	330
	Stroke Length		in	11.81	11.81
	Adjustment		in	11.81	11.81
Cushion Pad Area(LR×FB)		1	in	137.8×59.06	137.8×59.06
		2		149.61×59.06	149.61×59.06
		3		161.42×59.06	161.42×59.06
		4		173.23×59.06	173.23×59.06

* Upper die weight may vary in table size. Please contact your sales representative for more information.
** For selecting 132T, 165T and 220T air cylinder die cushions, bolster area in FB should be at least 66.93in.
*** For selecting 264T air cylinder die cushions, bolster area in FB should be at least 74.80in.
**** For SEL2-880-1, only 110T die cushion is available.

* For SEL4-880-1, only 110T die cushion is available
※ Slide and bolster area up to 216.53x61.02in by request.
※ This specification is subject to change without notice.

Products

SEL Series｜Straight Side Eccentric Gear Link-Motion Press

4 Points Straight Side Eccentric Gear Link-Motion Press Tandem Line+6-AXIS ROBOTS Intelligent Press that offers Total Solution

4 Points Straight Side Eccentric Gear Link-Motion Press Tandem Line+6-AXIS ROBOTS
Intelligent Press that offers Total Solution